6 hard variables that determine the 'base price per square meter'
1. Material Route: Natural/Artificial/Graphene Composite
- Natural graphite film: Expanded graphite rolling, short process, cheap raw materials, in-plane thermal conductivity of about 200-400 W/m · K, lowest price, about 100-200 yuan/㎡
- Artificial graphite film (PI carbonization): mainstream electronic heat dissipation, surface area 1200-2000 W/m · K, moderate price, about 150-300 yuan/㎡ (regular specifications; high-end high thermal conductivity grades are higher)
- Graphene composite film/high-purity pyrolytic graphite film: can reach 2000+W/m · K in-plane, with the advantage of thick film, but low yield, priced at 800-1800 yuan/㎡ or even higher
2. Thickness and tolerance
- Conventional 17 μ m/25 μ m/40 μ m/50 μ m
- Under the same brand: thinner, more expensive (due to greater process difficulty), but too thick sacrifices in-plane thermal conductivity
- Tolerance ± 2 μ m is more expensive than ± 5 μ m; Wide width (1.5m) is more expensive than narrow width
- Uneven thickness will directly lower the bonding yield, and the subsequent scrap cost is more expensive than the film itself
3. In plane thermal conductivity (don't just look at the peak value)
- The nominal 1500 and the measured 1500 are two different things
- Different testing standards (ASTM D5470/ISO 22007) and samples result in incomparable values
- The thicker the thickness, the lower the actual in-plane thermal conductivity of the same brand - buyers often pay an extra 30% premium for the "nominal 2000", but the actual installed capacity only reaches 1200
4. Vertical thermal conductivity and thermal resistance (most easily overlooked)
- Graphite film has high XY thermal conductivity, and typically only 5-30 W/m · K in the Z direction
- The equivalent thermal resistance of the adhesive layer at 8 μ m is significantly higher than that at 5 μ m
- The buyer only asked about "in-plane thermal conductivity" and ignored the Z-direction thermal resistance and contact thermal resistance. As a result, the film was purchased but the hot spot did not come off. Another layer of thermal pad was added, and the money was spent twice
5. Purity, ash content, yield
- High purity film with ash content<0.1%, long graphitization cycle, low yield, and doubled price
- The yield rate of artificial membrane is 95% compared to graphene membrane below 80%, resulting in a significant difference in cost per square meter
- Consumer electronics require 99% carbon content, while aerospace/semiconductors require 99.9%+
6. Width, roll length, minimum order quantity
- Wide width rolls (1m/1.5m) are cheaper than sheet materials, but there is a higher loss during changeover
- Small batch sampling: sold by roll, high unit price; Annual frame of 50000 square meters or more usually discounted by 15-25%
- Die cutting factories' "outsourcing+cutting" will add up gross profit, and direct procurement from the source substrate factory is more cost-effective
5 hardest hit areas where buyers overpay
❌1. Paying for the Three Words' Graphene '
Many products labeled as "graphene heat dissipation film" are actually repackaged with artificial graphene film.
- Don't believe it without CMA/CNAS report or SJ/T 11685 compliance statement
- Unless thermal simulation proves that the standard artificial membrane cannot withstand the temperature rise, there is no need to apply graphene composite
❌2. Pay for excess thermal conductivity
- Mid end mobile phone project, 1200 W/m · K is sufficient, with a hard 2000 brand, and the unit price is 40% higher
- Hot design did not conduct simulation, R&D "prefer high over low", procurement is fully accepted according to orders
❌3. The adhesive backing and film covering are not included in the total calculation
- Single sided PSA adhesive, PET release film, and insulation coating are all additional fees
- Insufficient temperature resistance of the adhesive (softening at 105 ℃), resulting in delamination and repair after aging of the entire machine, with rework costs exceeding 10 times the film price
- Correct approach: Choose adhesive (acrylic/silicone/thermal conductive adhesive) according to the working conditions, do not assume "just with adhesive"
❌4. Neglecting die-cutting loss and directionality
- Graphite film has directionality, with a die-cutting loss of 20-40% due to random layout
- Blind cutting of irregular parts according to CAD drawings, including burrs, powder loss, and waste pieces, will be included in the unit price
- Buying whole rolls and having the factory optimize the layout according to the diffusion direction saves 15-25% compared to buying "finished small pieces"
❌5. Treat the 'detection file' as a gift
- Asbestos free declaration RoHS/REACH, Third party reports on thermal conductivity and batch COAs must be included in the contract in advance
- Supplementing files and resending samples in the later stage delays project milestones, resulting in extremely high hidden costs
How to quote when purchasing to avoid being deceived
Ask the supplier not just 'how much does it cost per square meter', but to quote according to this list:
1. Material type (natural/artificial PI based/graphene composite)
2. Thickness + tolerance (e.g. 25 μ m ± 2 μ m)
3. In-plane/vertical thermal conductivity (with testing standards)
4. Width x roll length, bare film or adhesive, release film specifications
5. Purity/Ash/Sulfur and Chlorine (ppm)
6. Die cutting method (laser/die), layout utilization rate
7. Batch tiered pricing (1k/10k/50k ㎡)
8. Delivery time MOQ, Does it include COA + third-party reports
Real price comparison formula:
Effective cost = film price + adhesive/die-cutting loss + repair risk + document compliance cost
Not priced per square meter.
End
The price of thermal conductive graphite film is not determined solely by its thermal conductivity, but is determined by the material route, thickness tolerance, yield, adhesive structure, die-cutting loss, and compliance documents.
